Unpacking and levelingUnpackingRemove the washing machine from its packaging. Make sure that the washing machine has not been damaged during the transportation process. If it has been damaged, contact the retailer and do not proceed any further with the installation process. Remove the 4 protective screws (used during transportation) and the rubber washer with the corresponding spacer, located on the rear part of the appliance (see figure).Hotpoint Washing MachineClose off the holes using the plastic plugs providedKeep all the parts in a safe place: you will need them again if the washing machine needs to be moved to another location.Packaging materials should not be used as toys for children.if(typeof ez_ad_units!='undefined')ez_ad_units.push([[970,90],'manuals_plus-leader-3','ezslot_3',116,'0','0']);__ez_fad_position('div-gpt-ad-manuals_plus-leader-3-0');Leveling Install the washing machine on a flat sturdy floor, without resting it up against walls, furniture cabinets, or anything else.If the floor is not perfectly level, compensate for any unevenness by tightening or loosening the adjustable front feet (see figure); the angle of inclination, measured in relation to the worktop, must not exceed 2.Hotpoint Washing MachineLeveling the machine correctly will provide it with stability, help to avoid vibrations and excessive noise, and prevent it from shifting while t is operating. If it is placed on a carpet or a rug, adjust the feet in such a way as to allow a sufficient ventilation space underneath the washing machine.Connecting the electricity and water suppliesConnecting the water inlet hoseif(typeof ez_ad_units!='undefined')ez_ad_units.push([[300,250],'manuals_plus-square-4','ezslot_34',117,'0','0']);__ez_fad_position('div-gpt-ad-manuals_plus-square-4-0');Connect the supply pipe by screwing it to a cold water tab using a gas-threaded connection (see figure).Before performing the connection, allow the water to run freely until it is perfectly clear.Connect the inlet hose to the washing machine by screwing it onto the corresponding water inlet of the appliance, which is situated onthe top right-hand side of the rear part of the appliance (see figure). Make sure that the hose is not folded over or bent.The water pressure at the tap must fall within the values indicated in the Technical details table (see next page).If the inlet hose is not long enough, contact a specialized shop or an authorized technician.Never use second-hand hoses.Use the ones supplied with the machine.Connecting the drain hoseConnect the drain hose, without bending it, to a drainage cut or wall drain located at a height between 65 and 100 cm from the floor;Hotpoint Washing Machine
Setting the temperatureBy pressing the TEMPERATURE button to set the wash temperature (see Table of wash cycles).The temperature may be lowered, or even set to a cold wash ( ).The washing machine will automatically prevent you from selecting a temperature that is higher than the maximum value set for each wash cycle.Setting the spin speedBy pressing the SPIN SPEED button to set the spin speed for the selected wash cycle.The maximum spin speeds available for each wash cycle are as follows:if(typeof ez_ad_units!='undefined')ez_ad_units.push([[300,250],'manuals_plus-box-4','ezslot_13',103,'0','0']);__ez_fad_position('div-gpt-ad-manuals_plus-box-4-0');Wash cycles Cotton Maximum spin speedSynthetics1400 rpmWash cycles Cotton800 rpmWool600 rpmSilkdrain onlyThe spin speed may be lowered, or the spin cycle can be excluded altogether by selecting the symbol .The washing machine will automatically prevent you from selecting a spin speed that is higher than the maximum speed set for each wash cycle.Hotpoint Washing Machine FunctionsThe various wash functions available with this washing machine will help to achieve the desired results, every time.To activate the functions:
Hotpoint Washer Manuals
Below you can find all models Hotpoint Washing Machines for which we have manuals available. Also view the frequenty asked questions at the bottom of the page for useful tips about your product. Is your model not on the list? Please contact us.
0 Items in Cart Appliance Parts Blog Home
About Us
Locations
Careers
Policies
Contact
Member Login
Part Search: Appliance Model Search: Air Conditioner Parts - Room Air
Appliance Accessories
Appliances
*** CLOSEOUTS ***
Dishwasher Parts
Dryer Parts
Freezer Parts
HVAC Equipment
HVAC Parts
HVAC Supplies
Ice Machine
Icemakers and Parts
Microwave Parts
Range Hood - Vent Hood
Range Parts - Oven Parts
Refrigerator Parts
Refrigerator Water Filters
Repair Help
Trash Compactor Bags
Washer Parts
Water Filters
Water Heater
Wire & Terminals
We have a Hotpoint Electric Water Heater Cataloque number 100WBSC521035. It was here when we bought the house 25 years ago. It says 50 gallons on it but it is the size and shape of the washer and dryer which sit on either side of it. I am worried that it will cease to work sometime and I don't have a clue where to look for a similar new one.
2ff7e9595c
Comments